View HLD1045E_7749780.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 1 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 data display ag hld 1045e 10.4 inch highend tft-lcd display preliminary specification the information given in this document is carefully checked and believed to be reliable. data display reserves the right to make changes in product or specification at any time and without further notice. data display products are not intended for use in systems in which failures of product could result in personal injury. all mentioned trademarks are registered trademarks of their owner.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 2 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 1. overview 1.1 description: HLD1045E is a 10.4-inch tft-lcd (thin film transistor liquid crystal display) module composed of lcd panel, driver ics, control circuit, and backlight. by applying 6 bit digital data 640 x 480, 262k ? color images are displayed on the 10.4-inch diagonal screen. input power voltage is 5.0v (does not includes power for the backlight). both 3.3v- cmos and 5.0v-cmos voltage levels are acceptable for logic input voltage. inverter for backlight is not included in this module. 1.2 general features item specification display area (mm) 211.2 x 158.4 (10.39-inch diagonal) number of pixels 640(h) x 480 (v) pixel pitch (mm) 0.33 (h) x 0.33 (v) color pixel arrangement rgb vertical stripe display mode normally white number of colors 262k wide viewing angle technology optical compensation film optimum viewing angle (contrast ratio) 6 oclock 1 brightness (cd/m2) 400 power consumption (w) 8.5 module size (mm) 243.0 (w) x 181.6 (h) x 12.2 (d) module weight (g) 530 backlight unit ccfl, two lamps, replaceable 1 for projects 500 pcs. up also 12:00 v.a. available 1.3 product disclaimer the lcd products listed in this document are not suitable for safty related applications that do not have redundant back-up system(s). in other words, these lcd products are are not designed for use as a single source safety related application, and therefore, are not recommended for applications in which human life and/or environment may be affected in the event of the failure of the lcd product. more specifically, if there is no back-up system or product in place that will continue operating the system, the lcd products should not be used in such things as: aircraft navigation or aerospace equipment nuclear reactor control systems any application where failure or inaccuracy might cause death or personal injury (e.g. life support systems) or military and submarine critical systems. the lcd products are designed for typical industrial applications such as, but not are limited to the following: computers, office equipment, industrial controllers, audio and visual equipment, test and measurement devices, communication equipment, point of sale, medical imaging and automotive and various other consumer products. if there are any questions regarding the use, ability or application of these lcd products, please contact data display.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 3 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 2. absolute maximum ratings 2.1 environmental conditions: humidity 85% rh, no condensation item symbol min. max unit power supply voltage for lcd operating temperature storage temperature v cc t op t stg - 0.3 - 10 - 35 6.5 + 60 + 80 v c c 3. electrical characteristics 3.1 conditions: tft-lcd module ambient temperature is 25c item symbol min. typ. max. unit remark power supply voltage for lcd v cc 4.75 5.00 5.25 v power supply current for lcd i cc 200 ma permissive input ripple voltage v rp 100 mv p-p v cc =+5.0v high v lh 2.0 v cc v logic input voltage low v ll 0.0 0.8 v 3.2 backlight the table below shows data for one lamp only the tft-lcd module has two identical lamps operated independently operation of both lamps is required inorder to meet all the parameters in the HLD1045E specification. item symbol min. typ. max unit lamp voltage lamp current lamp starting voltage at 25 c at 0 c lamp frequency v l i l v s v s f l 3.0 810 1000 50 580 6.5* 7.0 80 v ma v v khz note*: for typical luminance of 400 cd/m2
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 4 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 3.3 notes vcc turn-on conditions: t1 10ms 0 < t2 50ms 0 < t3 50ms v cc -dip conditions: 2.7v v cc < 4.5v and td 10ms v cc < 2.7v v cc -dip conditions should also follow the v cc turn-on condition test condition for i cc typical: 64 gray-bar pattern 480 line mode v cc = +5v test condition for i cc (max): 1 x 1 checkerboard, black and white pattern dc input voltage = 4.75v
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 5 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 4. interface connectors pin assignment input connector type (see paragraph 6) input connector cn1: df9b-31p-1v(hirose) input mating connector: df9b-31s-1v(hirose) input connector pin assignment table pin symbol function 1 gnd ground* 2 dclk clock signal 3 hd horizontal sync signal 4 vd vertical sync signal 5 gnd ground* 6 r0 red data signal (lsb) 7 r1 red data signal 8 r2 red data signal 9 r3 red data signal 10 r4 red data signal 11 r5 red data signal (msb) 12 gnd ground* 13 g0 green data signal (lsb) 14 g1 green data signal 15 g2 green data signal 16 g3 green data signal 17 g4 green data signal 18 g5 green data signal (msb) 19 gnd ground* 20 b0 blue data signal (lsb) 21 b1 blue data signal 22 b2 blue data signal 23 b3 blue data signal 24 b4 blue data signal 25 b5 blue data signal (msb) 26 gnd ground* 27 dena data enable signal 28 v cc 5.0v power supply 29 v cc 5.0v power supply 30 test this pin should be open. test signal output for only test use 31 test this pin should be open. test signal output for only test use note: the metal frame of the tft-lcd module is connected to ground.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 6 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 backlight connector type (see paragraph 6) backlight connector (cn2 and cn3): bhr-02(8.0)vs-1n (jst) backlight mating connector: sm02(8.0)b-bhs(jst) backlight connector pin assignment table: pin number symbol function 1 cth vblh (high voltage) 3 ctl vbll (low voltage)
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 7 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 5. interface timing 5.1 timing chart
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 8 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 5.2 timing specification item symbol min typ max unit frequency f clk 25 mhz period t clk 34,5 40 ns width-low tw cl 12 ns width-high tw ch 12 ns rise time tr clk 5 ns dclk fall time tf clk 5 ns set up time t ds 5 ns data (r,g,b) hold time t dh 5 ns set up time t des 5 ns hold time t deh 5 ns low time tw dl 90 160 168 t clk rise time tr de 5 ns fall time tf de 5 ns horizontal front porch t hfp 0 16 t clk horizontal back porch t hbp 2 144 t clk vertical front porch t vfp 1 12 t h dena vertical back porch t vbp 2 33 t h frequency f h 27 31,6 38 khz period t h 730 800 808 t clk width-low tw hl 5 96 t clk rise time tr hs 10 ns hd* fall time tf hs 10 ns frequency f v 55 60,0 70 hz period t v 489 525 t h width-low tw vl 3 t h rise time tr vs 10 ns vd fall time tf vs 10 ns note: dclk and hd should be applied continuously at the input connector of the tft-lcd module during operation, subject to v cc turn-on conditions
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 9 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 5.3 color data assignment definitions gray scale: color (n) n indicates gray scale level data: 1=high, 0=low
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 10 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 6. block diagramm
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 11 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 7. mechanical specification 7.1 frontside drawing
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 12 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 7.2 rear side drawing
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 13 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 8. optical characteristics test conditions: ta=25c, v cc =5.0v, il=6.5ma, all measurements made using bm- 5a (topcon) or lcd-7000 (otsuka electronic) in a dark room, under no ambient light conditions. 8.1 summary table: item symbol condition min typ max unit contrast ratio cr = = 0 150 300 1 - luminance l = = 0 - 400 1 - cd/m2 tr = = 0 - 15 1 - ms response time tf = = 0 - 35 1 - ms horizontal - -60~ 60 - c viewing angle vertical cr 10 - -55~ 45 - c red x y 0.54 0.30 0.57 0.33 0.60 0.36 green x y 0.30 0.49 0.33 0.52 0.36 0.55 blue x y 0.14 0.15 0.17 0.18 0.20 0.21 color coordinates white x y = = 0 0.29 0.31 0.32 0.34 0.35 0.37 - 1) contrast, luminance and response time will be influenced in upper and lower temperatur range 8.2 definitions contrast ratio cr = on (white) luminance / off (black) luminance viewing angle ( , ) ? see drawing below:
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 14 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 8.3 definition of response time tr and tf: 9. reliability test conditions 9.1 temperature and humidity test item conditions high temperature and high humidity operation 40c, 90%rh 500 hours high temperature and high humidity storage 60c, 90%rh 96 hours low temperature storage - 20c, 96 hours thermal shock (non-operating) between - 20c (1 hour) and 60c (1 hour) 5 cycles 9.2 shock and vibration test item conditions shock (non operating) shock level: 1470 m/s2 (150g) waveform: half sinusoidal wave, 2ms number of shocks: one shock input in each direction of three mutually perpendicular axis for a total of six shock input vibration (non operating) vibration level: 9,8 m/s2 (1.0g) waveform: sinusoidal frequency range: 5 to 500 hz frequency sweep rate: 0.5 octave/min. duration: one sweep from 5 to 500 to 5hz in each of three mutually perpendicular axis (total 3 hrs.) judgment standard ? pass/fail criteria for reliability tests is defined as follow: pass: normal display image with no obvious non-uniformity defect fail: no display image, obvious non-uniformity, or line defect.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 15 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 10. life time of the backlight lamp definitions lamp end of life is defined as the luminance of it become half of the initial value the life time of the backlight lamp depends on the ambient temperature. the life time may be different from the time specified in the table below if the lamp is operated under extreme temperature conditions. specification item symbol condition min typ unit il=3.0ma, ta=25c 50,000 50,000 il=6.0ma, ta=25c 40,000 50,000 life time t l il=7.0ma, ta=25c 30,000 40,000 hours 11. handling precautions for tft-lcd modules assembly precautions please use the mounting hole on the module corners for installation and avoid bending or wrenching lcd during assembly process. do not drop, bend or twist the tft-lcd module during handling. guidelines for designing the tft-lcd module enclosure: housing case must be designed carefully so as not to put stresses on lcd all sides and not to wrench module. mechanical stress to the tft-lcd module made degrade the reliability and overall performances of the display (like brightness unformity degradation?etc.). keep sufficient clearance between lcd module back surface and housing when the lcd module is mounted. approximately 1.0 mm of the clearance in the design is recommended taking into account the tolerance of lcd module thickness and mounting structure height on the housing. when some parts, such as, fpc cable and ferrite plate, are installed underneath the lcd module, still sufficient clearance is required, such as 0.5mm. this clearance is, especially to be reconsidered when additional parts are inserted for emi countermeasures. choose carefully the inverter location to invoid any stress to the lamp cable. the lamp cable also should not interfere with the module installation into the enclosure. keep sufficient clearance between lcd module and the other components, such as inverter and speaker so as not to interfere with the lcd module. approximately 1.0mm of the clearance in the design is recommended. do not apply pressure or scratch lcd panel surface with anything hard. do not soil lcd panel surface by touching with bare hands. (polarizer film, surface of lcd panel is easy to be flawed.).
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 16 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 do not apply pressure or any parts on the rear side such as source tcp, gate tcp, control circuit board and fpcs during handling lcd module. if applying pressure to the tft-lcd module in unavoidable, handle the lcd module with care not to damage them. wipe out lcd panel surface with absorbant cotton or soft cloth to clean the surface. wipe out immediately any liquids which may have accidentally being sprayed on lcd panel surface. droplets on the lcd panel surface may alter the quality of the image. do not disassemble the tft-lcd module for any reasons. by doing so you would void the warranty of thr tft-lcd and is very likely that the performances will be degraded cosiderably. do not touch metal frames with bare hands and soiled gloves. if fingerprints or dirt are not cleaned immediately with solvent it is very likely that permanent marks will be left on the metal surface. disconnect the lamp wires before handling the inverter otherwise is possible to damage the lamp and/or the lamp wires by pulling it together with the inverter. operating precautions turn off the power supply before connecting and disconnecting signal input cable. do not change the setting of the adjustable resistors on the tft-lcd module subassemblies. the adjustable resistors are properly set at the factory and any deviation from the factory setting will compromise the performances on the tft- lcd module. when evaluating the optical characteristics of the display please note that will take longer time for the backlight to stabilize if the ambient temperature is at the lower end of the temperature range. sudden changes of the ambient temperature may cause condensation on various surfaces of the tft-lcd module and degrade the overall performances until the surface becomes dry again. follow up the general safety rules applying to generic electronic products. precautions with electronics this lcd module uses cmos integrated circuits and other components subject to be affected by electrostatic discharges. use esd protection equipment and follow all esd safety procedures when handling the tft-lcd modules. please remove protection film very slowly from the surface of lcd module to prevent from high level electrostatic discharges. it is recommended to lift the protection film starting from the corner of the glass in proximity of the source and gate pwb ending at the corner of the glass furthest away from the electronics.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 17 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 storage precautions when you store lcds for a long time, it is recommended to keep the temperature between 0c ~ 40c without the exposure of sunlight and to keep the humidity less than 90%rh. do not leave the lcds in the environment of high humidity and high temperature such as 60c 90%rh, 80c with low humidity only. do not expose the tft-lcd modules to temperatures below ?35c. safety precautions when disposing lcds it is recommended to break them into pieces. the broken pieces should be washed with solvents such as acetone and ethanol. the residual solvent from this process should be burned. if any liquid leaks out of damaged glass cell and corners in contact with the hands, wash it of thoroughly with soap and water. others exposing the tft-lcd module to strong incident light may negatively affect the display characteristics because of polarizer film, color filter and other materials degradation. do not expose lcd module to direkt sunlight or light with strong ultraviolet content. avoid any contact of the tft-lcd module front surface with other objects or materials. packaging and shipping packaging box and inner case for lcd are designed to protect the lcds from the damage or scratching during transportation. do not open the packaging box unnecessarily. do not stack more than 5 boxes on top of each other because stack of 5 is minimum designed limit. do not turn over the boxes. avoid excessive shock, the shipping boxes are not designed to be thrown, excessive vibrations can also damage the boxes and the tft-lcd modules inside. packaging box and inner structures of it are made of cardboard. avoid to have the boxes in contact with water or in high humidity environment which may cause the carton to become soft, or to break, damaging the tft-lcd modules.
title: 10.4? highend tft lcd module specifications number: hld 1045e rev. 1 page 18 of 18 data display ag industriestrasse 1 d-82110 germering mar 2001 http://www.datadisplay.de tel.: +49-89-894450-0 fax: +49-89-894450-90 contents 1. overview .......................................................................................... 2 1.1 description. .......................................................................................... 2 1.2 general features.................................................................................. 2 1.3 product disclaimer ............................................................................... 2 2. absolute maximum ratings......................................................... 3 2.1 environmental conditions ...................................................................... 3 3. electrical characteristics ...................................................... 3 3.1 conditions ............................................................................................ 3 3.2 backlight .............................................................................................. 3 3.3 notes ................................................................................................... 4 4. interface connectors pin assignment .................................. 5 5. interface timing ............................................................................ 7 5.1 timing chart......................................................................................... 7 5.2 timing specification ............................................................................. 8 5.3 color data assignment ......................................................................... 9 6. block diagramm ............................................................................. 10 7. mechanical specification ........................................................... 11 7.1 frontside drawing ................................................................................ 11 7.2 rear side drawing................................................................................ 12 8. optical characteristics............................................................. 13 8.1 summary table ..................................................................................... 13 8.2 definitions ............................................................................................ 13 8.3 definition of response time tr and tf: ................................................... 14 9. reliability test conditions........................................................ 14 9.1 temperature and humidity.................................................................... 14 9.2 shock and vibration ............................................................................. 14 10. life time of the backlight lamp ................................................ 15 11. handling precautions for tft-lcd modules ........................ 15

▲Up To Search▲

Price & Availability of HLD1045E

	To Download HLD1045E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .